LK166
Home >> Download >> MITSUBISHI >> Manual Download >> MITSUBISHI A1SX20EU User's Manual PDF

MITSUBISHI A1SX20EU User's Manual PDF

Brand: MITSUBISHI
Product model: A1SX20EU
Name: I/O Module
Sort: User's Manual
File language: English
File size: 5.14MB
For common cathode input module and leaky type output module (2 line type).Input type: DC input, negative public end.
Input points: 16 points.
Enter the response time: 1 A1SX20EU PDF. 5ms the following.
Rated input voltage / current: DC24V/7mA.
External connection: 2~4 line type.
Waterproof connector type.
Strong waterproof type of IP67 protection grade.
No need to stop the system can be replaced module A1SX20EU
Without the use of tools can be a simple connection, save time.
Terminal resistor built-in.
Can be installed along the 6 direction.
Hardware simulation method is to use a number of hardware equipment to simulate the generation of the signal,
The signals are connected to the input end of the PLC system in a hard wired way, and the timeliness is strong A1SX20EU PDF.
Software simulation method is in the MITSUBISHI PLC in the preparation of a set of simulation program,
The simulation provides the field signal, which is simple and easy to operate, but it is not easy to guarantee the timeliness A1SX20EU PDF.
Simulation of the process of debugging, debugging method can be used to segment, and the monitoring function of programmer. Output points: 32 points.
Voltage: AC100 ~ 240V.
OFF leakage current: 3mA.
Output type: bidirectional controlled silicon MITSUBISHI User's Manual.
Response time: 0.5Hz+1ms.
8 points / a common end.
38 point terminal station.
With short circuit protection.
With the surge absorber.
Each scanning process. Focus on the input signal sampling. Focus on the output signal to refresh.
Input refresh process. When the input port is closed,
Program in the implementation phase, the input end of a new state, the new state can not be read MITSUBISHI User's Manual A1SX20EU Manual.
Only when the program is scanned, the new state is read.
A scan cycle is divided into the input sample, the program execution, the output refresh.
The contents of the component image register are changed with the change of the execution of the program MITSUBISHI User's Manual.
The length of the scan cycle is determined by the three.
CPU the speed of executing instructions.
Time of instruction.
Instruction count.
Due to the adoption of centralized sampling.
Centralized output mode.
There exist input / output hysteresis phenomena, i.e., the input / output response delay.
PLC selection with the development of PLC technology, more and more types of PLC products,
Function is becoming more and more perfect, and its application is more and more extensive.
Different series of different models of PLC has different performance, applicable occasions also have different emphasis,
Price also has a greater difference. Therefore PLC selection,
Under the premise of meeting the controol requirements,
Should consider the best performance to price ratio, a reasonable choice of PLC A1SX20EU User's Manual.
System program memory for storing system program,
Including management procedures, monitoring procedures, as well as the user program tto do the compiler to compile the process of interpretation A1SX20EU Manual.
Read only memory. Manufacturers use, content can not be changed, power does not disappear.
Related products
MITSUBISHI
DC source type input module
A1SX71
MITSUBISHI DC source type input module A1SX71
Type of input: DC source. Input points: 32 po
MITSUBISHI
Input module
A1SX40-S2
MITSUBISHI Input module A1SX40-S2
Type of input: DC leakage. Input points: 16 p
MITSUBISHI
Input module
A1SX40-S1
MITSUBISHI Input module A1SX40-S1
Type of input: DC leakage. Input points: 16 p