LK166
Home >> Products >> MITSUBISHI >> FX series PLC >> FX all modules and accessories >> FX2N module >> FX2N-48ET-DSS Input / output module MITSUBISHI FX2N-48ET-DSS

FX2N-48ET-DSS Input / output module MITSUBISHI FX2N-48ET-DSS

Brand: MITSUBISHI
Name: Input / output module
Model: FX2N-48ET-DSS
Input and output points: 48 points.
DC power supply: DC24V.
Input points: 24 points.
Output points: 24 points.
Output form: transistor output (source).
Weight: 0.85kg.
Input signal voltage: DC24V.
FX2N series expansion unit
Expansion unit is an input and output expansion device with a built-in power supply.
As with the basic unit, the extension unit can be connected to a variety of input and output and special extension equipment.
Can connect to FX3GA/FX3G, FX3GE and FX3U.
AC power model, the built-in maximum DC24V 250mA/460mA supply power.
Because all models of FX series are built in high speed counter,
So the high speed control can be realized by the simple procedure.
The input of the basic unit is built in the anti jitter filter,
One part as digital filter,
Sensitivity adjustment unit can reach 1ms.
Using high speed counter automatically adjusted to the minimum value.
Through the high cost of the built-in positioning function and the expansion function to increase the number of control axis.
Extended function expansion board and special adapter,
Data links and communication with external serial devices.

Max input / output points: 10 points.
Supply voltage: 100 - 240VAC.
Input points: 6 points.
Output points: 4 points.
Output type: relay.
Power consumption (W): 19.
Weight (kg):0.22.
Size (WxHxD) mm:60x90x49.
Host has 10 points (6I/4O), 14 points (8I/6O), 20 points (12I/8O), 30 points (16I/14O) of 4 types MITSUBISHI FX2N-48ET-DSS.
This type of PLC is mainly used in all of the digital input, digital output control point of the device FX2N-48ET-DSS
Can be directly connected to the 220V city power, built-in 8K step EEPROM memory, no battery, easy to maintain.
The series transistor output (MT) of the PLC, can be output 2 100KHz pulse, direct drive servo or stepper motor.
The series PLC can not be brought with the expansion module, but can be installed by the BD board to extend a small amount of I/O MITSUBISHI FX2N-48ET-DSS.
The series 1N through the installation of BD series PLC board, can achieve RS232, RS485, RS422 communication. Analog input: 2.
Analog output points: 1 points.
Weight: 0.1kg.
FX3 series can be connected to the 2 channel input (voltage: DC0~10V, or current DC4~20mA), as well as 1 channel output (DC0~10V, or current: DC4~20mA) of the adapter MITSUBISHI FX2N-48ET-DSS.
Each channel can be specified as a current input or voltage input.
Connecting FX3SA, FX3S, FX3GA, FX3G, and FX3U main body, the need to convert the adapter or function expansion board. Max input / output points: 48 points FX2N-48ET-DSS MITSUBISHI.
Supply voltage: 100 - 240VAC.
Input points: 24 points.
Output points: 24 points.
Output type: transistor.
Power consumption: 50VA.
Weight (kg):0 FX2N-48ET-DSS MITSUBISHI. 85.
Size (WxHxD) mm:182x90x87.
Note recording function, Component annotation can be recorded in the program register.
Online program editor, online change the program will not lose the working hours or stop production operation.
RUN/STOP switch, running on panel / stop switch easy to operate FX2N-48ET-DSS MITSUBISHI.
Remote maintenance, remote programming software can monitor, upload or uninstall programs and data via modem communications
Password protection, usingg a eight digit password to protect your program FX2N-48ET-DSS.
Clock function and hour meter function, all of the PLC FX2N has a real-time clock standard.
Continuous scanning function, to define the operation cycle for the application off the continuous scan time MITSUBISHI FX2N-48ET-DSS.
Input filter adjustment function, you can use the input filter to smooth the input signal (in the basic unit x000 to x017).


...More relevant models >>>>