MITSUBISHI GT1030-LWD Connection Manual (Mitsubishi plc Connections) PDF

Cable length: 3.0m.
For the connection between QnAS/AnSCPU/ motion controller GOT (A Series) and CPU.
Applicable models: GT16, GT15, GT11. USB interface protection cover on the front panel of the host computer (for replacement) GT1030-LWD PDF.
For 15 inches /12.1 inches /10.4 inches /8.4 inches.
Applicable model: GT15. Cable length: 30m.
The connection between the FXCPU (MINI-DIN8 pin connector) and the graphic operation terminal GT1030-LWD
Connection between FXCPU communication function extension board (MINI-DIN8 pin connector) and GOT.
Applicable models: GT10, GT21. A series of high performance models that are widely used in network or single machine work environments GT1030-LWD PDF.
Screen size: 8.4 inches.
Display color: 16 color.
Mounting type: panel mounting type.
Resolution: VGA (640 x 480).
Display device: TFT color.
Host frame color: black.
Power type: AC100~240V.
Communication interface: with built-in RS-422.
Ideal model for high performance in a network or independent operation environment GT1030-LWD PDF.
User storage capacity: 9MB (GT15__-VNB_:5MB).
Device USB port.
Standard RS-232 interface.
Support video /RGB unit.
If the capacitive touch screen is in the middle of the operation, the display resolution or display mode of the touch screen is changed again,
Or the refresh rate of the touch screen controller is adjusted by itself, and the cursor and the touch point can not be felt when the cursor is not corresponding to the touch point,
Must be re calibrated to the touch screen system MITSUBISHI Connection Manual.
In order to ensure the normal operation of the touch screen system, in addition to ensure the proper installation of the system software,
Must also remember that in a host do not install two or more than two kinds of touch screen driver,
This will cause the system to run in conflict, so that the touch screen system can not be used properly MITSUBISHI Connection Manual MITSUBISHI Connection Manual. 15 inches.
Applicable model: GT27. Series: multimedia and advanced features and features of a variety of high-performance models.
Screen size: 10.4 inches.
Display color: 256 color or more color.
Mounting type: panel mounting type.
Resolution: VGA (640 x 480).
Display device: TFT color.
Host frame color: black.
Power type: AC100~240V.
Communication interface: with built-in RS-422.
High performance models with multimedia and advanced features and functionality (including embeddedd communications capabilities) GT1030-LWD Manual .
User storage capacity: 15MB (GT16__-VNB__:11MB).
With HOST USB and device USB port.
Standard Ethernet, RS-422/485 and RS-232 ports.
Support multimedia and video /RGB units.
Analog touch panel.
Do not let the touch screen surface with water drops or other soft things stick to the surface,
Otherwise, the touch screen is easy to mistake that there is a hand touch caused by surface acoustic wave screen is not allowed.
In addition to cleaning the dirt on the surface of the touch screen,
You can use a soft dry cloth or a cleaning agent to clean out the center of the screen carefully,
Or use a dry soft cloth dipped in industrial alcohol or glass cleaning fluid to clean the touch screen surface.
Touch screen response is slow if you use a hand or other touch to touch the surface acoustic wave touch screen,
This shows that it is likely that the touch screen system has been obsolete, the internal clock frequency is too low,
Or because there is water in the surface of the touch screen to make the touch screen mobile, rapid response recovery,
To replace or upgrade the system must, or usse dry cloth touch screen on the surface of the water GT1030-LWD Connection Manual.
If the user is operating the touch screen, the direction of the touch move is to the left,
But the cursor of the system moves to the right,
The failure may be due to the conneection of the control box and the touch screen connected to the connector or the touch screen,
Users as long as the direction of the re exchange of it GT1030-LWD Manual .