LK166
Home >> Products >> MITSUBISHI >> FX series PLC >> FX3U series PLC >> FX3U-48MR/DS PLC MITSUBISHI FX3U-48MR/DS

FX3U-48MR/DS PLC MITSUBISHI FX3U-48MR/DS

Brand: MITSUBISHI
Name: PLC
Model: FX3U-48MR/DS
Max input / output points: 48 points.
Power supply voltage: 24VDC.
Input points: 24 points.
Output points: 24 points.
Output type: relay.
Power consumption: 35W.
Weight (kg):0.85.
Size (WxHxD) mm:182x90x86.
Built in CPU, power supply, input and output. By using a rich variety of functional extension boards and special adapters,
Can achieve high precision control.
Based on the function of FX2N has been greatly strengthened and enhanced.
High speed operation.
Basic instructions: 0.065 s/ instruction.
Application instruction: 0.642 s/ instruction.
Large capacity memory.
Built in program memory 64000 steps.
Flash memory cartridge with program transfer function.
Authentication。
Corresponding EN and UL/cUL authentication.
Faster and more efficient. Support high speed control and network communication, and have the function of data recording.
High speed, large capacity, multi-function high-end machine.
FX3U supports high speed processing, CC-Link communication, network communication, analog control and advanced positioning system.
Connected to the CC-Link, including the remote I/O, the maximum input and output control points up to 384 points,
Can correspond to a variety of field needs, the use of its scalability and flexibility to expand the scope of application of the control system.
Third generation high function micro programmable controller.
High speed, high efficiency, high performance, large capacity, and new features.
Built in high speed processing and positioning.
Control points: maximum 256 points.
Use CC-Link remote I/O for 384 points.

Max input / output points: 14 points.
Supply voltage: 100 - 240VAC.
Input points: 8 points.
Output points: 6 points.
Output type: Transistor (source).
Power consumption (W): 6.5.
Weight (kg):0.22.
Size (WxHxD) mm:60x90x49.
Host has 10 points (6I/4O), 14 points (8I/6O), 20 points (12I/8O), 30 points (16I/14O) of 4 types MITSUBISHI FX3U-48MR/DS.
This type of PLC is mainly used in all of the digital input, digital output control point of the device FX3U-48MR/DS
Can be directly connected to the 220V city power, built-in 8K step EEPROM memory, no battery, easy to maintain.
The series transistor output (MT) of the PLC, can be output 2 100KHz pulse, direct drive servo or stepper motor.
The series PLC can not be brought with the expansion module, but can be installed by the BD board to extend a small amount of I/O MITSUBISHI FX3U-48MR/DS.
The series 1N through the installation of BD series PLC board, can achieve RS232, RS485, RS422 communication. Memory format: EEPROM.
Number of steps: up to 16000 steps can be used.
Battery support: do not.
Method for writing and deleting: the device is installed on the PLC, and is written and deleted by the peripheral device MITSUBISHI FX3U-48MR/DS.
Note: built-in extension. Max input / output points: 20 points.
Supply voltage: 100 - 240VAC.
Input points: 12 points.
Output points: 8 points.
Output type: Transistor (source).
Power consumption (W): 20.
Weight (kg):0 FX3U-48MR/DS MITSUBISHI. 4.
Size (WxHxD) mm:75x90x75.
All equipment is digital input and output point.
The total I/O points are not more than 30 points, and the input points are less than 16, the output points are less than 14 FX3U-48MR/DS MITSUBISHI.
Its MT series of PLC can drive 2 way servo or stepper, commonly used in the control system for a simple manipulator.
MITSUBIISHI FX1S series PLC is suitable for the smallest package,
It is the preferred target for low cost users to seek powerful control over a limited range of I/0 FX3U-48MR/DS MITSUBISHI FX3U-48MR/DS.
FX1S provides up to 30 I/O points, and caan be transmitted through serial communication data,
MT models also have the ability to locate, widely used in a variety of small mechanical equipment MITSUBISHI FX3U-48MR/DS.


...More relevant models >>>>