LK166
Home >> Products >> Yaskawa >> Servo driver / motor >> SGD7S/SGD7W series >> SGM7A type servo motor >> SGM7A-70A7A61 | Yaskawa SGM7A-70A7A61 Low inertia, high speed servo motor

SGM7A-70A7A61 | Yaskawa SGM7A-70A7A61 Low inertia, high speed servo motor

Brand: Yaskawa
Name: Low inertia, high speed servo motor
Model: SGM7A-70A7A61
Low inertia, high speed servo motor type SGM7A (rated speed 3000r\/min).
Rated output: 7.0kw.
Power supply voltage: AC200V.
Serial encoder: 24 bit absolute value type.
Design sequence: A.
Shaft end: straight shaft with keyway, with screw.
Optional parts: no purchase pieces.
Small (about 80% in the past).
Equipped with high-resolution 24bit encoder (16 million 770 thousand \/rev pulse).
The maximum torque of 350% (small capacity).
Hope to shorten the working cycle.
Want to improve positioning accuracy.
Increase speed after shaking.
Whether there is no workpiece, action is not stable.
It is helpful to the servo performance of ultra high speed and ultra precision control. most
To limit the performance of the device to solve the problem

Full closed loop module.
Maximum applicable motor capacity: 2.0kw.
Power supply voltage: three phase AC200V.
Interface: analog voltage, pulse sequence type (rotary servo motor).
Design sequence: A.
Hardware specification: base mounting type (standard).
Matching (software): no matching (standard) Yaskawa SGM7A-70A7A61.
Matching (parameters): no matching (standard).
Optional modules: full closed loop module SGM7A-70A7A61
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed on the side of the machine to realize the high precision and high response.
External encoder capable of corresponding high resolution (linear grating) Yaskawa SGM7A-70A7A61. Sigma -V series servo motor SGMSV.
Rated output: 5.0kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal, with the brake (DC24V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit) Yaskawa SGM7A-70A7A61.
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous SGM7A-70A7A61 Yaskawa.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type SGM7A-70A7A61 Yaskawa.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection SGM7A-70A7A61 Yaskawa.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationServo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 4.4kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: high precision machine tool.
Shaft end: straight shaft without key.
Optional parts: with oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,,
Alarm can only turn off the main circuit power supply, easy to maintain SGM7A-70A7A61.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 Yaskawa SGM7A-70A7A61.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control


...More relevant models >>>>