LK166
Home >> Products >> Yaskawa >> Servo driver / motor >> SGDM series >> SGMSH type motor >> Super high power motor SGMSH-20ACA2B Yaskawa SGMSH-20ACA2B

Super high power motor SGMSH-20ACA2B Yaskawa SGMSH-20ACA2B

Brand: Yaskawa
Name: Super high power motor
Model: SGMSH-20ACA2B
Servo motor SGMSH type.
Rated speed: 3000r\/min.
Power: 2.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: straight shaft without key.
Optional parts: with DC90V brake.
Ultra high power response series: the need for small inertia, high torque.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regenerative resistance connection terminals.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistor

High performance, use the best type of servo unit (purpose type).
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: single phase AC100V.
Interface: MECHATROLINK-III communication command type (linear servo motor).
Design sequence: B.
Hardware specifications: paint.
Interface: fixed point through output function Yaskawa SGMSH-20ACA2B.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models SGMSH-20ACA2B
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device Yaskawa SGMSH-20ACA2B.
FT005 (support for rotary table purposes): with the rotation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table.
FT006 (fixed point through the output function): no need to pass through the upper device can be set through the output (Chu Fa).
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller Yaskawa SGMSH-20ACA2B. Sigma -V series servo motor SGMSV.
Rated output: 5.0kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit absolute value type (standard) SGMSH-20ACA2B Yaskawa.
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal, with the brake (DC90V).
Super power rate SGMSH-20ACA2B Yaskawa.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15 SGMSH-20ACA2B Yaskawa.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resiistance grade: F SGMSH-20ACA2B.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) Yaskawa SGMSH-20ACA2B.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation


...More relevant models >>>>
Related download