LK166
Home >> Products >> Yaskawa >> Servo driver / motor >> SGDV type >> SGDV-____25 Type (Used by linear servo motor) >> Yaskawa SGDV-2R8A25A Servo driver for linear servo motor

Yaskawa SGDV-2R8A25A Servo driver for linear servo motor

Brand: Yaskawa
Name: Servo driver for linear servo motor
Model: SGDV-2R8A25A
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.

Large capacity SGMVV type servo motor.
Rated output: 30KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit delta.
Rated speed: 800r/min.
The main mechanical structure: support mounting type, straight shaft (with keyway and screw).
Optional parts: with hold brake (DC90V).
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties Yaskawa SGDV-2R8A25A SGDV-2R8A25A
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r/min and 1500r/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen Yaskawa SGDV-2R8A25A.









Servo motor type SGMPH (speed: 3000r\/min).
Power: 0.2kw.
Power supply voltage: single phase AC100V.
Serial encoder: 16 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw.
Optional parts: with oil seal, DC24V brake.
Partial flat series: the need to install the servo motor in a small space.
Flexible user system Yaskawa SGDV-2R8A25A.
For you to build the best system to enrich the product line to support you.
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operatedEquipped with INDEXER functional type servo unit (kit type).
Maximum applicable motor capacity: 11kw.
Power supply voltage: three phase AC200V.
Interface: instruction selection and installation (rotary type servo motor).
Matching (hardware): shelf installation type + paint.
Matching (software): standard.
Matching (parameter): standard.
Optional module: INDEXER+ full closed loop module.
Simple.
By programming and serial programming, easy implementation of motion control.
Can also be installed through the Windows environment support tool (SigmaWin+) easy to start.
The I/O module can be connected with the upper controller simply.
Smart.
To support the operation of the main purpose of the positioning operation based on the program table.
The maximum number of proggrammable positioning points to 256 points SGDV-2R8A25A.
With external positioning, JOG speed table operation, the origin of reversion, rich features such as programmable signal output.
I/O points for the input: 19 points, output: 16 points.
Speedy. SGDV-2R8A25A.
High speed and high precision positioning by combining with high performance V series.
Motion control can be realized without using motion controller.


...More relevant models >>>>