Sigma -V series servo motor SGMGV.
Rated output: 2.9kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: no matching.
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Transport machinery.
Food processing machinery.
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Single axis servo driver SGD7S.
Maximum applicable motor capacity: 0.4kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-III communication command type (Chinese market is RJ-45 connector). ఼
Design sequence: A.
Hardware options: paint.
It is helpful to the servo performance of ultra high speed and ultra precision control Yaskawa SGMGV-30DDA61.
Maximize the performance of the device, to solve the problem
SGMGV-30DDA61
Single axis servo unit.
Speed frequency response 3.1kHz.
Best use: in order to release the EX\/FT specifications.
Vibration suppression function.
For the inability to improve the speed loop gain of the machine,
Can reduce the velocity fluctuation by cogging motor.
Smooth driveEquipped with INDEXER functional type servo unit (kit type) Yaskawa SGMGV-30DDA61.
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: three phase AC200V.
Interface: instruction selection and installation (linear servo motor).
Matching (hardware): base mounting type (standard).
Matching (software): standard.
Matching (parameter): standard.
Optional module: INDEXER+ full closed loop module.
Simple.
By programming and serial programming, easy implementation of motion control Yaskawa SGMGV-30DDA61.
Can also be installed through the Windows environment support tool (SigmaWin+) easy to start.
The I/O module can be connected with the upper controller simply.
Smart.
To support the operation of the main purpose of the positioning operation based on the program table.
The maximum number of programmable positioning points to 256 points.
With external positioning, JOG speed table operation, the origin of reversion, rich features such as programmable signal output.
I/O points for the input: 19 points, output: 16 points.
Speedy.
High speed and high precision positioning by combining with high performance V series.
Motion control can be realized without using motion controller.Servo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 0.3kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: straight shaft without key.
Optional parts: with DC24V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMGV-30DDA61.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGMGV-30DDA61.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control