Input and output points: 48 points.
AC power supply: AC100~240V.
Input points: 24 points.
Output points: 24 points.
Output form: relay output.
Input signal voltage: DC24V.
Expansion unit is an input and output expansion device with a built-in power supply.
As with the basic unit, the extension unit can be connected to a variety of input and output and special extension equipment.
Can connect to FX3GA/FX3G, FX3GE and FX3U.
AC power model, the built-in maximum DC24V 250mA/460mA supply power.
So the high speed control can be realized by the simple procedure.
Sensitivity adjustment unit can reach 1ms.
Using high speed counter automatically adjusted to the minimum value.
Through the high cost of the built-in positioning function and the expansion function to increase the number of control axis.
Data links and communication with external serial devices.
Max input / output points: 24 points.
Power supply voltage: DC24V.
Input points: 14 points.
Output points: 10 points.
Output type: transistor.
Power consumption (W): 32.
Size (WxHxD) mm:90x90x75.
FX1N series is a very powerful micro PLC, can be extended to up to 128 I/O points,
And can increase the special function module or the expansion board FX2N-48ER-ES/UL MITSUBISHI.
Communication and data link function options make FX1N in the volume, communication and special function modules and other important applications is very perfect FX2N-48ER-ES/UL
A PLC unit can output 2 100KHz pulses at the same time,
PLC is equipped with 7 special positioning instructions,
Including zero return, absolute position readout, absolute or relative drive, and special pulse output control FX2N-48ER-ES/UL MITSUBISHI. Axis of control: 1.
Program memory: built-in 3.8k step EEPROM.
Applicable PLC:FX1N, FX2N, FX3U, FX2NC (to FX2NC-CNV-IF).
Applicable PLC:FX3UC (to FX2NC-CNV-IF or FX3UC-1PS-5V).
Not only can deal with single speed positioning and positioning,
Can also carry on the multi section fast operation and so on complex control.
Can not be connected to the PLC, while running alone FX2N-48ER-ES/UL MITSUBISHI.
1 can control 1 axes,
FX1N, FX2N, PLC FX3U up to 8 units can be connected,
PLC FX2NC up to 4 units can be connected,
FX3UC PLC can connect up to 7 units, and a plurality of shafts can be independently controlled.
Can output up to 200kHz of the pulse train.
The connection function of the absolute position detection function and the manual pulse generator.
Can be used in the form of flow chart programming software, visual programming. Max input / output points: 32 points.
Power supply voltage: 24VDC.
Input points: 16 points.
Output points: 16 points.
Output type: Transistor (source).
Power consumption: 25w.
Size (WxHxD) mm:150x90x87.
Developed a range of special function modules to meet the needs of different - analog I/O, high speed counter.
Positioning control to achieve the 16 axis, the pulse train output or for the J and K type thermocouple or Pt sensor developed the temperature module.
A total of 8 special function modules can be configured for each FX2n main unit.
Note recording function, Component annotation can be recorded in the program register.
Online program editor, online change the program will not lose the working hours or stop production operation.
RUN/STOP switch, running on panel / stop switch easy to operate.
Remote maintenance, remote programming software can monitor, upload or uninstall programs and data via modem communications
Password protectiion, using a eight digit password to protect your program FX2N-48ER-ES/UL.
Clock function and hour meter function, all of the PLC FX2N has a real-time clock standard.
Continuous scanning function, to define the operation cycle for the application off the continuous scan time FX2N-48ER-ES/UL.
Input filter adjustment function, you can use the input filter to smooth the input signal (in the basic unit x000 to x017).